Strong 210+108E Dental Micromotor 35000 RPM Handpiece For Dental Lab Polisher Micromotor

Item Type:Electric Manicure Drill & Accessory Output voltage:other Material:Plastic Model Number:strong drill 210+108E No-Load Speed:35000rpm strong 210+108E Dental micromotor 35000 RPM handpiece for dental lab polisher micromotor SIZE: 15*8*5CM

Packing List: 210 Control Box +108E handpiece Pedal+ carbon brush Handpiece Holder We have three chuck optional:

2.35mm/3.0mm/3.175mm. Standard is 2.35mm. If you use is different,

please when you take order must remark.And we use plug, standard is EU plug.

If you need others please remark when you take an order.

Precautions:

1. When the handle is used, no water can enter and the bearing will rust. If it enters the water, it must

be dismantled on the same day to clean the water, dry it and use it again (to extend the bearing life). 2. When installing the grinding head, the flying dust on the grinding head rod must be wiped clean and

then placed inside the chuck (the service life of the chuck can be extended). 3. The use of the foot switch must be turned off the power of the host,otherwise it will affect the

performance of the host circuit (seriously can cause the motherboard to short circuit or burn). 4. When the handle is used, the handle should not be idling, and the grinding pin must be installed

(to avoid damage to the bearing and the spindle). 5. Do not touch, especially the handle. 6. Do not refuel the bearings

Power:65W Model Number:strong drill 210+108E Item type:dental drill & accessory Rotary speed:0~35000rpm Item weight:2.5kg Packing List: 210 Control Box +108E handpiece Pedal+ carbon brush Handpiece Holder ① When the handle is used, the handle should not be idling,

and the grinding pin must be installed. ② When installing the grinding head, the rod of the grinding head must be cleaned and cleaned,

and then loaded into the chuck. ③ Don't let water in when you are using the handpiece otherwise the handpiece will be rust.

It must clean the water out and make it dry then continue to use if water go into to handpiece. ④ The use of the foot switch must be turned off the host power,

otherwise it will affect the performance of the host circuit. ⑤ Don’t hit or make it fall down, especially the handle. ⑥ It is strictly forbidden to refuel the bearings. We have three chuck optional:

2.35mm/3.0mm/3.175mm. Standard is 2.35mm. If you use is different,

please when you take order must remark.And we use plug, standard is EU plug.

If you need others please remark when you take an order.

Precautions:

1. When the handle is used, no water can enter and the bearing will rust. If it enters the water, it must

be dismantled on the same day to clean the water, dry it and use it again (to extend the bearing life). 2. When installing the grinding head, the flying dust on the grinding head rod must be wiped clean and

then placed inside the chuck (the service life of the chuck can be extended). 3. The use of the foot switch must be turned off the power of the host,otherwise it will affect the

performance of the host circuit (seriously can cause the motherboard to short circuit or burn). 4. When the handle is used, the handle should not be idling, and the grinding pin must be installed

(to avoid damage to the bearing and the spindle). 5. Do not touch, especially the handle. 6. Do not refuel the bearings

About product information:

Different product batches, some information of the product may be different from the actual product,

please use the actual product information (the final interpretation right belongs to the company).

Adult toy material: plastic Adult toy material: plastic Adult toy material: plastic Adult toy material: plastic Adult toy material: plastic Adult toy material: plastic Adult toy material: plastic Adult toy material: plastic Adult toy material: plastic Adult toy material: plastic Adult toy material: plastic Adult toy material: plastic Adult toy material: plastic Adult toy material: plastic Adult toy material: plastic